Advance Techo

Tensile Tester tackle the toughest tests with their superior axial alignment, stiffness, and crosshead guidance. A simple design allows for lower cost, faster delivery, and years of maintenance free operation. All eXpert systems are capable of performing compression tension, and flexure tests.

Taller, shorter, wider, faster, slower: Our engineering group will configure a design to meet your specifications. A second actuator can also be added for performing biaxial tests.

• Bench top models from 2kN to 50kN provide the flexibility to test adhesives, biomaterials, elastomers, metals films, packaging, plastics, textiles wire and other materials with confidence.
• Floor standing models from 50kN to 200kN feature wide column spacings to accommodate large specimens, larger grips and fixtures, temperature chambers, special test fixtures and full-size parts.
• Exceeds all AT/ISO accuracy requirements.

We have established ourselves as a renowned manufacturer, supplier and exporter of a vast array of Toe Cap Impact Testers. Our range is used for determining the performance of toes of protective boots. The professionals hired by us use high-grade material and other components in the manufacturing process that are sourced from most trustworthy vendors of the market. These products are highly applauded by the customers for their corrosion resistance, minimal maintenance and sturdy construction.

We have gained expertise in manufacturing, supplying and exporting a quality range of Flexometer. Advanced technology and latest machines are employed in the production process so that our range is in compliance with international quality standards.

We have gained expertise in manufacturing, supplying and exporting a quality range of Bennewart Flex Testers. Advanced technology and latest machines are employed in the production process so that our range is in compliance with international quality standards. The products made available by us are used for testing the physical properties a footwear's sole. These products can be availed by the customers in various specifications as per their requirements.

The Advance Techo Bursting Strength Tester is designed to find bursting strength of fabric/leather/paper/paper board. A test specimen is held between two annular clamps under sufficient pressure to minimize slippage. The upper clamping surface which is in contact with the test specimens has a continuous spiral grooves. A circular diaphragm of pure gum rubber is clamped between the lower clamping plate & pressure cylinder so that before the diaphragm is stretched by pressure underneath it the center of its upper surface is below the plane of the clamping surface.
Capacity                                      :   0 to 7kg/cm² × 0.2 kg/cm² least count &
                                                          0 to 40 kg/cm² × 1 kg/cm² least count
Opening in upper clamp        :   30.5 mm diameter
Opening in lower clamp         :   38.1 mm diameter
Rate of fluid displacement    :   95 cc/ minute
Test fluid                                    :   Glycerin
Gear Box                                     :   Worm reduction type
 
Power required                        :   220 VAC, 500 W, 50 Hz single phase 
The equipment is fitted with a motor driven cam mechanism, which increases fluid displacement on the lower side of the diaphragm at a specified rate. The equipment is fitted with an arrangement, which automatically brings down the pressure and stops the motor on completion of the test cycle. A maximum reading type digital pressure gauge gives the bursting pressure.
 
The equipment is raggedly designed to give a long & trouble free life. The components are brighter chrome plated or painted in metallic paint to give the tester an aesthetic appearance.

Additional Information:

• Item Code: 0mkl
• Production Capacity: 500
• Delivery Time: Ready Stock
• Packaging Details: Wooden

Determination of effect of ageing on various physical properties of different materials may be carried out by heating the material under test inside an air oven so that the effects of long term ageing are reproduced within a much shorter duration of time .for this determination, physical properties of the material under test are determined before ageing and ageing the test specimen at the specified temperature for a set duration of time and subsequent to the room temperature before conducting the tests again.

Determination of various physical characteristics of different materials and products at elevated temperature may be carried out by heating the test specimen to the appropriate temperature inside a constant temperature air oven and determining the required characteristics with the specimen kept under the same temperature. For this purpose the equipment needed for conducting the determination can either be kept inside the oven along with the test specimen, or if this is not feasible because of certain constrains, by taken the heated specimen out from the oven and conduction the test in still air within the shortest possible span of time.

Additional Information:

• Item Code: 015
• Production Capacity: 100
• Delivery Time: ready stock
• Packaging Details: wooden packing

Launderometers offered by us comprise a digitally controlled, electrically heated double walled water bath. We use Al stainless steel in manufacturing the inside walls of the bath. Further, the outer walls are manufactured using mild CRCA sheet, which is duly enameled. The heater is used in order to heat the bath. This has a temperature controller device which is controls the temperature of water inside the bath. The temperature is displayed on a digital indicator. During test, the specimens and test solution are kept in stainless steel jars. Furthermore, the jars have rubber seals for avoiding water leakage.

 

We are prominent manufacturers, Suppliers & exporters of high-quality Cone Calorimeter from Delhi-NCR, India. AT Cone Calorimeter is used for the determination of the fire behavior of the various samples in the solid state. The Cone Calorimeter Device is used to collect information of the various parameters associated with the burning characteristics such as ignition time, mass loss, combustion products, heat release rate etc. of various samples.

The test method is based on the observation that, generally, the net heat of combustion is proportional to the amount of oxygen required for combustion. The relationship is that approximately 13,1 × 103 kJ of heat is released per kilogram of oxygen consumed. Specimens in the test are burned under ambient air conditions while being subjected to a predetermined external irradiance within the range of 0 kWm−2 to 75 kW m−2 and measurements are made of oxygen concentrations and exhaust gas flow rates. Asian Cone calorimeter is manufactured considering the Client requirements & by using high-quality material

Technical Data:

• Cone-shaped radiant electrical heater: 5 000 W at 230 VAC
• Irradiance control: PID type up to 10000C
• Weighing device: 1000 GM X 0.1 GM least count
• Ignition circuit: spark plug powered from a 10 kV transformer
• Oxygen analyzer: paramagnetic type, with a range of at least 0 % oxygen to 25 % oxygen
• Heat flux meters: up to (100 ± 10) kW m−2
• Calibration burner: square orifice with an area of (500 ± 100) mm2
• Data collection and analysis system: NI software

Related Standards

• BS ISO 5660-1:2015
• ISO 5660-1:2015(E)

Additional Information:

• Production Capacity: 100
• Delivery Time: 35 Days
• Packaging Details: wooden box

The “AT” Din Abrasion Tester is designed Pouch Compression Tester with Motor/gear box and screw Model with constant rate of traverse.

• Suitable for testing the Seal Integrity of Liquid / Gas Filled - Pouches / Sachets / Blister-packs.
• Suitable for 100 ml – 1,500 ml or larger packs.

Additional Information:

• Item Code: pouch

Additional Information:

• Item Code: ATPC
• Production Capacity: 15
• Delivery Time: 5 DAYS
• Packaging Details: WOODEN BOX

We are engaged in supplying of superior quality Digital Specific Gravity Balance to our valued customers spread across the nation.

A test specimen of the textile together with Blue Wool Standard is exposed under prescribed conditions to the light from an artificial light source. The colour fastness of the specimen is assessed by comparing its performance with that of blue wool fastness standards.